Run with systemd · Next · OpenBao Kubernetes KMS

Repeat this procedure on every control-plane node. At the end, the provider runs as the non-root openbao-kms user, listens on /run/openbao-kms/kms.sock, and has passed doctor against OpenBao.

Before you begin

Download and verify the artifact in Download the release , and keep that shell with VERSION and ARCH set.
Have the reviewed output from Generate installation files and complete Prepare OpenBao .
Obtain the OpenBao CA bundle as ca.crt and the provider host JWT as identity.jwt from your identity provisioning process. The JWT must be renewable without the protected API server.

If your values use auth.jwt.source: oauth2, stage the client secret and issuer CA bundle instead of identity.jwt in the steps below; see OAuth 2.0 client credentials . The service unit supports both sources.

Step 1: Install the package or tarball

On Debian or Ubuntu:

terminal

sudo dpkg -i "bao-kms-provider_${VERSION}_linux_${ARCH}.deb"

On RHEL-family hosts:

terminal

sudo rpm -Uvh "bao-kms-provider_${VERSION}_linux_${ARCH}.rpm"

On other hosts, install the systemd tarball. The commands need GNU install, systemd-sysusers, and systemd-tmpfiles; hosts without them must create the same layout through configuration management, as described in Security: Linux identity model . Extract the archive and enter its versioned directory:

terminal

tar -xzf "bao-kms-provider_${VERSION}_systemd_linux_${ARCH}.tar.gz"
cd "bao-kms-provider_${VERSION}_systemd_linux_${ARCH}"

Run the following block in a root shell from the extracted directory. It installs the files and creates the service identities and directories. It leaves live configuration and authentication material unchanged.

terminal

set -eu
install -D -o root -g root -m 0755 bin/bao-kms-provider /usr/bin/bao-kms-provider
install -D -o root -g root -m 0644 systemd/bao-kms-provider.service /usr/lib/systemd/system/bao-kms-provider.service
install -D -o root -g root -m 0644 sysusers.d/openbao-kms.conf /usr/lib/sysusers.d/openbao-kms.conf
install -D -o root -g root -m 0644 tmpfiles.d/openbao-kms.conf /usr/lib/tmpfiles.d/openbao-kms.conf
install -D -o root -g root -m 0644 config/provider-systemd.yaml /usr/share/doc/bao-kms-provider/examples/provider-systemd.yaml
install -D -o root -g root -m 0644 kubernetes/encryption-config.yaml /usr/share/doc/bao-kms-provider/examples/encryption-config.yaml
install -D -o root -g root -m 0644 README.md /usr/share/doc/bao-kms-provider/README.md
install -D -o root -g root -m 0644 LICENSE /usr/share/doc/bao-kms-provider/LICENSE
systemd-sysusers /usr/lib/sysusers.d/openbao-kms.conf
systemd-tmpfiles --create /usr/lib/tmpfiles.d/openbao-kms.conf

Reload systemd to register the unit:

terminal

systemctl daemon-reload

The package and tarball leave the service disabled and stopped.

Step 2: Copy the generated files

Copy the reviewed generated/ directory from Generate installation files to the node, next to ca.crt and the credential. Read generated/node-setup.sh before you run it: it is plain sh, and every path, owner, and mode comes from generated/config.yaml.

Run it without arguments to print its phases and the identity fingerprint:

terminal

sh generated/node-setup.sh

Compare the fingerprint with generated/installation.json and your recorded cluster identity. Every node must print the same fingerprint.

Step 3: Run the node setup phases

Run each phase as root, in order. Each phase prints what it changed and the command for the next one, and stops with a non-zero exit status when something is wrong.

terminal

sudo sh generated/node-setup.sh prepare
sudo sh generated/node-setup.sh install --ca ca.crt --credential identity.jwt
sudo sh generated/node-setup.sh check
sudo sh generated/node-setup.sh start

Phase	What it does
`prepare`	Checks the host tools, the package files, the `openbao-kms` user, and the socket group. Creates any missing credential or CA directory.
`install`	Installs `config.yaml`, the CA bundle, and the credential with the owner and mode the service user needs. Stops if any of them already exists.
`check`	Runs `config`, `verify-key`, and `doctor` as the `openbao-kms` user and confirms the fingerprint.
`start`	Enables and starts `bao-kms-provider.service`, then waits for HTTP 200 from `/ready`. Runs only after a passed `check` within the last hour.

For native OAuth, pass the client secret as --credential, and the issuer CA bundle as --issuer-ca when the configuration sets auth.jwt.oauth2.caCertFile; see OAuth 2.0 client credentials .

install refuses a node that already has a deployment. For an existing node, follow Operate: Upgrade instead and keep its identity and state.

check exits with status 4 when verify-key or doctor reports a [fail] check. Failures on a new setup are usually policy or auth problems; see Operate: Troubleshooting and Reference: CLI . Read any [warn] lines before you run start.

After the local API server starts using the socket, check its access with the API server’s own identity:

terminal

sudo sh /usr/share/bao-kms-provider/probe-apiserver

For a tarball installation, use sudo sh bin/probe-apiserver from the extracted kit. The helper requires pgrep, awk, setpriv, and exactly one local running kube-apiserver. Status, Encrypt, and Decrypt must pass. A root API server produces a warning because the check does not prove non-root access.

If start times out waiting for /ready, check journalctl -u bao-kms-provider.service for these common first-start causes:

host DNS is not ready when the service starts,
the OpenBao TLS server name does not match the certificate,
the credential is expired or has the wrong audience or subject.

Continue to Enable encryption once the provider is ready on every control-plane node.

About the unit

The installed unit comes from deploy/systemd/bao-kms-provider.service. The settings that matter for the control-plane boot path:

Setting	Purpose
`Before=kubelet.service`	Orders process execution before kubelet when both units start together. It does not require kubelet to start this unit.
`Type=exec`	Completes startup ordering after successful execution of the provider binary. It does not wait for the KMS socket or `/ready`.
`ConditionPathExists=`	Skips a start attempt when the configuration is absent; start the unit after staging it. The provider validates the selected authentication source during startup.
`ConditionPathIsDirectory=/run/openbao-kms`	Requires the socket directory that tmpfiles creates.
`User=openbao-kms`, `SupplementaryGroups=openbao-kms-socket`	Runs without root; the socket group is how the API server connects.
`Restart=always` with start limits	Restarts transient failures without hiding a fast crash loop.
`ProtectSystem=strict`, `ReadWritePaths=/run/openbao-kms /var/lib/openbao-kms/state`	Makes the host read-only except the socket directory and non-secret registry state.
`CapabilityBoundingSet=`, `NoNewPrivileges=true`	Runs without Linux capabilities or privilege escalation.

Enable the provider on every control-plane host. A missing, disabled, failed, or unready provider does not prevent kubelet from starting. The API server must retry its KMS connection during bootstrap; the unit does not gate or stop kubelet on readiness. Before a planned API server restart, check /ready.

network-online.target orders the start but does not prove DNS, routing, or OpenBao are reachable. The provider retries its initial checks for bootstrap.graceTimeout before it exits. For the full hardening surface, see Security: Hardening .